McIntosh MC2205 Endstufe Power Amplifier

 

Angeboten wird eine, aus gutem Grund sehr gesuchte Vintage Stereo Endstufe von McIntosh.  Die McIntosh MC2205 kommt aus Sammlerhand und ist entsprechend in einem fantastischen Zustand. Optik wie auch Klang zum niederknien. 

Genau das richtige Investment bei unserer derzeitigen Marktlage!

 

Output

stereo: 200W+200W (Output power)

14.1VRMS (at the time of a 1-ohm load intensity)

20.0VRMS (at the time of a 2-ohm load intensity)

28.3VRMS (at the time of a 4-ohm load intensity)

40.0VRMS (at the time of an 8-ohm load intensity)

mono: 400W (Output power)

14.1VRMS (at the time of a 0.5-ohm load intensity)

20.0VRMS (at the time of a 1-ohm load intensity)

28.3VRMS (at the time of a 2-ohm load intensity)

40.0VRMS (at the time of a 4-ohm load intensity)

Output load impedance stereo: 1 ohm, 2ohm, 4ohm, 8ohm

mono: 0.5 ohm, 1ohm, 2ohm, 4ohm

Output-power band 20Hz - 20kHz

THD (at the time of both ch(es) drive) 0.1% or less (Outputs 0.25W-200W, 20Hz - 20kHz)

Cross modulation distortion 0.1% or less (at the time of an Output power)

Frequency characteristic (at the time of 1W output) 20Hz-20kHz+0 -0.25 dB

10Hz-100kHz+0 -3.0 dB

SN ratio 95dB or more (at the time of an Output power)

Output voltage 25V

Dumping factor

stereo: 16 (at the time of a 1-ohm load intensity)

50 (at the time of a 2-ohm load intensity)

30 (at the time of a 4-ohm load intensity)

16 (at the time of an 8-ohm load intensity)

mono: 16 (at the time of a 0.5-ohm load intensity)

50 (at the time of a 1-ohm load intensity)

30 (at the time of a 2-ohm load intensity)

16 (at the time of a 4-ohm load intensity)

Input sensitivity/impedance 0.75V, 2.5V/100kohm

The semiconductor used Silicon transistor: 49 pieces

Silicon diode: 45 pieces

IC: Eight pieces

Power source 120V, 50Hz/60Hz

Power consumption 70W (at the time of a non-signal)

550W (at the time of a maximum rating output)

Dimensions Front panel: Width 411.2x181mm in height

Main unit: Width 381x height 166.7x depth of 368.3mm

Weight 38.6kg

44.0kg (at the time of an original packaging)

 

K236

3.790,00 €

  • 45 kg
  • verfügbar
  • 3 - 5 Tage Lieferzeit1

McIntosh mc402 Endstufe

 

Selten angebotener McIntosh Kraftprotz in top Erhaltungszustand. Die McIntosh MC402 Endstufe kommt aus gutem Hause und wurde nur sporadisch an Sonus Faber Lautsprechern genutzt. 

Original Bedienungsanleitung und Zertifikat gehören zum Lieferumfang.

5.890,00 €

  • 65 kg
  • verfügbar
  • 3 - 5 Tage Lieferzeit1

 

Weiterführende Informationen:

 

Specifications

Specifications

Power Output Stereo

Minimum sine wave continuous average power output per

channel, all channels operating is:

400 watts into 2 ohm load

400 watts into 4 ohm load

400 watts into 8 ohm load

Power Output Mono Parallel

Minimum sine wave continuous average power output is:

800 watts into 1 ohm load

800 watts into 2 ohm load

800 watts into 4 ohm load

Output Load Inpedance

2, 4 or 8 ohms (Stereo Mode)

1, 2 or 4 ohms (Mono Mode)

Rated Power Band

20Hz to 20,000Hz

Total Harmonic Distortion

Maximum Total Harmonic Distortion at any power

level from 250 milliwatts to rated power output is

0.005%

Intermodulation Distortion

Maximum Intermodulation Distortion if instantaneous peak output per channel does not exceed

twice the rated output, for any combination of frequencies from 20Hz to 20,000Hz, with all channels

operating is 0.005%

Dynamic Headroom

2.1dB

Frequency Response

+0, -0.25dB from 20Hz to 20,000Hz

+0, -3dB from 10Hz to 100,000Hz

Sensitivity

2.0 Volts Unbalanced Input

4.0 Volts Balanced Input

A-Weighted Signal To Noise Ratio

94dB Unbalanced (120dB below rated output)

98dB Balanced (124dB below rated output)

Input Impedance

10,000 ohms Unbalanced Inputs

20,000 ohms Balanced Inputs

Wide Band Damping Factor

Greater than 40

Power Requirements

100 Volts, 50/60Hz at 12 amps

110 Volts, 50/60Hz at 11 amps

120 Volts, 50/60Hz at 10 amps

220 Volts, 50/60Hz at 5 amps

230 Volts, 50/60Hz at 5 amps

240 Volts, 50/60Hz at 5 amps

Note: Refer to the rear panel of the MC402 for the correct

voltage.

Overall Dimensions

17-1/2 inches (44.45cm) W, 9-7/16 inches (23.97cm) H, 20

inches (50.8cm) D, including clearance for connectors

Weight

110.5 pounds (50.1kg) net, 143.5 pounds (65.1kg) in shipping carton

McIntosh MC300 Endstufe Power Amplifier

 

McIntosh MC300 Endstufe Power Amplifier in top Erhaltungszustand!

Für manch einer DER musikalischste unter den Macs.

 

Output power (20Hz - 20kHz, succession sine wave) stereo: 300W+300W (2ohm, 4ohm, 8ohm)

mono bridge: 600W (4ohm, 8ohm, 16ohm)

mono parallel: 600W (1ohm, 2ohm, 4ohm)

Output load impedance stereo: 2 ohms, 4ohm, 8ohm

mono bridge: 4 ohms, 8ohm, 16ohm

mono parallel: 1 ohm, 2ohm, 4ohm

Output-power bandwidth 20Hz - 20kHz

THD (at the time of both channel operation 20Hz - 20kHz) A maximum of 0.005% (250mW-300W)

Cross modulation distortion

(at the time of bothchannel operation 20Hz - 20kHz) A maximum of 0.005% (250mW-300W)

Frequency characteristic 20Hz-20kHz+0 -0.25 dB

10Hz-100kHz+0 -3 dB

SN ratio (A-standard) 105dB (below an Output power)

Dumping factor 40 or more

Input impedance 20kohm

Input sensitivity 1.4V (full)-2.5V (it1 position)-0

Power guarding Non clipping, THD<2% (1kHz >= 14dB)

Power source 100V, 50Hz/60 Hz, 0.6-12A (Underwriters Laboratories/CSA specification)

Dimensions (a knob, a termination included) Width 445x height 179x depth of 480mm

187mm (leg included) in height

Weight 35.8kg

 

K238

3.500,00 €

  • 45 kg
  • verfügbar
  • 3 - 5 Tage Lieferzeit1